Stack of blank hoodies for DTF printing in black, sport grey, navy and forest green at F&H Print, NYC Garment District

Best Blank Hoodies for DTF Printing (2026 Guide): How to Pick Plain Hoodies That Print Well and Sell

Quick answer, because some of you are standing at a heat press right now: the best blank hoodies for DTF printing are 8 oz or heavier cotton-poly fleece with a smooth face and no seam running through the chest. The Gildan 18500 is the one we sell the most of, by a mile. If you're in New York, we keep them on the shelf at 146 W 29th Street, right next to the DTF transfers, so you can press the same afternoon.

Stack of blank hoodies for DTF printing in black, sport grey, navy and forest green on a worktable at F&H Print, NYC Garment District
Blank hoodies ready for DTF printing at our shop on West 29th Street.

Now the longer story.

Last spring a guy came in with a box of forty hoodies he'd bought online for a bachelor party. Nice looking blanks. Soft. Cheap. He wanted a full-color crest on each chest by Thursday. We pressed one as a test and the white underbase went pinkish within about ten seconds of cooling. Red dye, cheap fleece, hot press. He ended up buying forty 18500s from us and the original box is still in his trunk, probably. That's the whole reason this guide exists.

Why the blank matters more than people think

Everybody says DTF is forgiving, and it is. The transfer doesn't care if the hoodie is cotton, poly, a blend, nylon, canvas. You can stick it to a tote bag or a cap. So people assume the hoodie itself doesn't matter much.

It matters a lot. We've got a shelf of "never again" blanks in the back to prove it. Three things in particular.

The first is the surface. A DTF print is a thin skin of ink and glue sitting on top of the fabric. On a tight, smooth knit it lies flat and looks like it was printed straight on. On a loose, hairy knit, the glue has to bridge little gaps between fibers, and after a couple of washes you get hairline cracks wherever the fabric bends. Elbows, the belly, the spot where the pocket meets the body. A customer brought one back last winter and the crack ran right through the middle of his kid's face. Not a great conversation.

The second is weight. Light hoodies (anything under about 7 oz) stretch when you pull them over your head, and the print moves with them. Heavy fleece doesn't move as much. Also, and this is just business, a heavy hoodie feels like a $50 hoodie. People pick it up off the table and nod. A thin one feels like a $20 hoodie no matter what's printed on it.

The third is dye. Some blanks, mostly reds, royals, and anything bright, let go of their dye when you hit them with 300 degrees. The dye creeps up into the white underbase of your transfer and tints it. That's dye migration. It's a polyester thing mostly, but bargain cotton blends do it too, which is what happened to the bachelor party guy.

Get the blank right and the press does the rest. Get it wrong and you can't fix it with more pressure or more time. We've tried. There's a 2 AM version of us that tried very hard.

What to look for in a blank hoodie for printing

Close-up comparing a smooth tight-knit hoodie fleece face with a loose fuzzy knit that cracks under DTF prints
Left: the smooth, tight face you want. Right: the fuzzy knit that cracks after a few washes.

Here's what we check when a new blank shows up at the shop. It takes about thirty seconds per hoodie once you've done it a few times. I do it to hoodies in department stores now, which nobody asked for.

Weight. We want 8 oz or more. The 18500 is 8 oz exactly. The streetwear-style blanks run 10 to 14 oz and feel it. Anything 7 oz or lighter is a spring hoodie and will show every wrinkle under the print.

Fabric. A 50/50 or 80/20 cotton-poly blend is the sweet spot. The cotton gives the adhesive something to bite into; the poly keeps it from shrinking and pilling. Pure cotton prints beautifully but shrinks more, so if you're doing a full-chest graphic on 100% cotton, wash the blank first or your centered logo won't be centered anymore.

The chest. Flip the hoodie around and look at the front panel. Some zip-ups and fashion blanks have a seam running down the middle. That seam will push a 12-inch print off to one side, or you'll have to shrink the art, and either way the customer notices. A standard pullover with the pocket starting low gives you a clean 12 by 14 inch canvas.

Face vs. fleece. Turn it inside out. The fuzzy brushed side should be inside. The outside should be smooth and tight. If you can clearly see the knit from arm's length, you'll see it in the print too.

Color. White, black, sport grey, navy, dark green: all safe. Red, royal blue, purple, anything neon: test first. If you have to print on those, drop the press to around 270 to 280°F and go a few seconds longer.

Sizing. Boring, but it's where small shops lose money. One brand we tried had a large that fit like an XL in the first case and like a medium in the second. Returns ate the margin, and then some. We still have eleven of them. Gildan, Bella+Canvas, and Independent are consistent case to case, which is most of why we stock them.

Peeling DTF transfer film off a black blank hoodie on a heat press to reveal a full-color print
Cold peel on a heavyweight black hoodie. The right blank makes this part boring, in a good way.

Our picks: the best blank hoodies for DTF printing

Gildan 18500 Heavy Blend Hoodie

This is the hoodie half of New York prints on. Walk down 29th Street on a Saturday and count them. 8 oz, 50/50, double-lined hood, pouch pocket, something like forty colors, and it costs less than a sandwich in Midtown. The face is smooth enough for small text, the blend barely shrinks, and it takes a 300°F press without flinching. If you need fifty hoodies by Friday for a team, an event, a merch drop, whatever, this is the answer. We stock it in the shop and ship it anywhere in the US.

Gildan 18000 Heavy Blend Crewneck

Same fabric, no hood, no drawstrings in the way. If you're printing a big front graphic, the crewneck gives you more clean space. It's also the one people buy when they want that faded "college sweatshirt" look, usually in sport grey, usually in a size up.

Independent Trading Co. IND4000

When someone says "I want something heavier than Gildan," this is what we hand them. 10 oz, 80/20, boxier cut, thick hood. The face is tighter than the 18500 so fine detail looks sharper. Roughly twice the price. If you're charging $60 or more for the finished piece, it's worth it; if you're selling at $35, it isn't, and we'll tell you so.

Bella+Canvas 3719 Sponge Fleece

Lighter at 7 oz, with a retail, slimmer fit. Not the toughest hoodie here, but it's the softest, and the sponge fleece surface is so smooth that DTF looks almost like direct-to-garment on it. Good for boutique labels and women's lines. Go easy on the heat; 280°F is plenty. We scorched one the first week we carried it, so, you know, learn from us.

Comfort Colors 1567

The washed-out, pigment-dyed look that's everywhere right now. 9.5 oz, 80/20, already looks ten years old in a good way. Prints great, better than we expected honestly. One warning: garment-dyed blanks sometimes give up a little dye on the first press, so cover with parchment and peel slow.

Which blank for which job?

People ask us to just tell them, so: team or event merch, grab the 18500 and don't overthink it. Streetwear brand, go Independent IND4000 or heavier, because your customer is going to judge the weight before they judge the print. Boutique or a women's line, Bella+Canvas 3719. That faded, thrifted look, Comfort Colors 1567. Big front graphic and you don't want a hood in the way, the 18000 crewneck. That covers about ninety percent of what walks through our door.

Blank Weight / blend Best for Press temp
Gildan 18500 hoodie 8 oz, 50/50 Teams, events, bulk merch 300°F
Gildan 18000 crewneck 8 oz, 50/50 Big front graphics, vintage look 300°F
Independent IND4000 10 oz, 80/20 Streetwear, premium drops 300°F
Bella+Canvas 3719 7 oz, sponge fleece Boutique, women's lines 280°F
Comfort Colors 1567 9.5 oz, 80/20 garment-dyed Faded / thrifted look 280°F
Heat press setup for DTF printing on a hoodie at 300°F with parchment paper, heat tape and transfer film
Everything you need for a hoodie press: 300°F, parchment, heat tape, and patience for the cold peel.

How to DTF print on a hoodie (the settings we actually use)

We get asked for "the settings" constantly, so here they are, taped to the wall above our press.

Pre-press the hoodie for five seconds first. Fleece holds moisture, especially in a New York August, and moisture makes transfers lift at the corners. Lay the transfer face down, and if it's a big one, tape it with heat tape so it doesn't creep when you close the press. Then 300°F, 12 to 15 seconds, medium-firm pressure. For Bella+Canvas and any garment-dyed blank, back off to 280 and go the full 15.

Let it cool before you peel. We're a cold-peel shop. Hot-peel films exist and some people love them, but on heavy fleece a cold peel gives you a cleaner edge and we've never been able to argue with that. Then cover with parchment or a Teflon sheet and press again for 5 to 10 seconds. That second press is the whole trick. It sinks the ink into the fleece and turns the finish matte and soft instead of plasticky. Skip it and the print feels like a sticker.

Then don't wash it for 24 hours. The adhesive is still curing. Customers always want to wash it that night and we always say please don't.

If you order transfers from us, these settings are printed on the packing slip, because we got tired of answering the phone about it.

DTF vs. screen printing on hoodies

Still the most common question we get after "do you have it in black."

Screen printing wins when you're doing a huge run of one simple design in one or two colors. Past about a hundred pieces, the per-unit cost drops below DTF, and screen ink sinks into fleece in a way a transfer doesn't quite copy. If you're printing 500 navy hoodies with a white one-color logo for a school, screen print them.

DTF wins at basically everything else. Full color, photos, gradients, tiny runs, mixed sizes, names and numbers, and anything you need tomorrow. No screens, no setup fee, no minimum, and the same transfer works on a black hoodie or a white one. Most of the small brands and shops we deal with are doing somewhere between one and two hundred pieces at a time, and for them DTF is the practical answer. We moved almost entirely to DTF a few years ago and haven't missed the screens.

Cases of wholesale blank hoodies stacked inside F&H Print, a DTF printing shop in Manhattan's Garment District
Case quantities of blank hoodies and crewnecks, in stock at 146 W 29th Street.

Buying blank hoodies wholesale without getting burned

If you're buying by the case, a few things we wish someone had told us.

Buy one of each size first. Press them, wash them twice, then commit to the case. It costs you a week and saves you a return pile.

Keep each order to one dye lot. Two lots of "black" are two slightly different blacks, and they show up in product photos. Customers notice before you do.

Budget for 3 to 5 percent spoilage. Even the good brands send the occasional dropped stitch or oil spot. Price it in and stop being surprised.

And buy close to home when you can. Freight on a case of hoodies adds up fast. If you're in the city, picking up from us on 29th Street almost always beats shipping, and you can put your hands on the blanks before you buy, which is worth more than people think.

We sell Gildan hoodies and crewnecks by the piece and by the case, and you can put DTF transfers or UV DTF stickers in the same order so it all shows up together.

Frequently asked questions

What are the best blank hoodies for DTF printing?

For most shops, the Gildan 18500 Heavy Blend: 8 oz, 50/50 fleece, smooth face, consistent sizing, cheap. If you're selling premium streetwear, step up to the Independent Trading Co. IND4000 at 10 oz, 80/20.

Can you DTF print on 100% cotton hoodies?

Yes, and it bonds beautifully. Just pre-wash the blank. Pure cotton fleece shrinks more than a blend, and a logo that was centered before the wash can sit crooked after it.

What temperature do you press DTF on a hoodie?

300°F (150°C) for 12 to 15 seconds at medium-firm pressure, cold peel, then a 5 to 10 second second press under parchment. Drop to around 280°F for lightweight or garment-dyed blanks.

Are plain hoodies and blank hoodies the same thing?

Same thing. "Plain hoodies," "blank hoodies," and "hoodie blanks" all mean an undecorated hoodie sold for printing or embroidery. "Wholesale blank hoodies" usually just means case quantities at a lower unit price.

How much do blank hoodies cost?

A Gildan 18500 runs roughly $14 to $20 a piece retail and less by the case. Independent and Comfort Colors land around $25 to $35. The 12 oz and up fashion-weight blanks can be $40 or more before you've printed a thing.

Where can I buy blank hoodies for printing in NYC?

F&H Print, 146 W 29th Street, in the Garment District. We stock Gildan hoodies, crewnecks, tees, polos, and hats, plus DTF transfers, UV DTF stickers, film, ink, and powder. Monday through Saturday, 9 to 6. Or order online and we ship nationwide.

Will DTF crack on a hoodie?

Not if the blank has a tight face and you do the second press. Cracking almost always traces back to a loose, fuzzy knit, a skipped second press, or a hot wash inside the first 24 hours. Cold wash, inside out, tumble low, and it'll outlast the hoodie.

Ready to print?

Grab your blanks, upload your art to a DTF gang sheet, and we'll turn it around fast. If you're nearby, come by the shop on West 29th and we'll pull a hoodie off the shelf so you can feel it before you buy. If you're not, we ship to all 50 states.

Shop blank hoodies   Order DTF transfers

Back to blog

Leave a comment